#USB AUDIO DRIVER INSTALL#
#USB AUDIO DRIVER MOD#
#USB AUDIO DRIVER SERIAL#
#USB AUDIO DRIVER WINDOWS 7#
#USB AUDIO DRIVER DOWNLOAD#

Should turn Red and the 101D should be keyed. On the FT-8 'Radio Tab' click on the 'TEST CAT'īutton. The computer you should be able to test both CAT and PTTįunctions. The Keyword is ' Enhanced'Īt this point if you connected the rear USB from the radio to Will read 'Silicon Labs Dual CP210x USB to UART Bridge EnhancedĬOM Port (COMx)' where (COMx) in my windows setup is COM 9, it

#USB AUDIO DRIVER INSTALL#

USB Driver (Virtual COM Port Driver) ? fromĪfter you install the driver verify it is working by using

#USB AUDIO DRIVER DOWNLOAD#

The first thing to do is download and install the ? FTDX101D/MP If you can assist me in any way it would be very much appreciated!

Itself and will have to guide him through each step. Will be done remotely so I will not have access to the radio I don't own the radio myself but I am trying to assist an elderlyĭisabled HAM get on air with FT8 and other digital modes. I was wondering if you could assist me with the settings for theġ01D that you used, both radio menu settings and wsjt-x. On 2:17 PM, Neil College via Groups.Io wrote: That's pretty much what I did to get CAT control and modulation Signal (you may need more or less - just adjust RPORT gain to keepĪLC in the White). 'RPORT' GAIN to 12 to prevent ALC distortion of the transmitted I also found that on FT-8 I had to turn down the

#USB AUDIO DRIVER MOD#

Go to Radio Settings, MODE SSB and select SSB MOD SOURCE 'REAR'.Īlso select REAR SELECT 'USB'. The 101D and modulate the radio with a single tone. Now run WSJT-X FT8 and activate the 'TUNE' button. The same Radio Tab click on the 'TEST CAT' button.

#USB AUDIO DRIVER SERIAL#

Under CAT CONTROL, Serial Port dropdown box select the Enhancedĭata Bits = 8, Stop Bits 1 and Handshake - NoneĪt this point if you connected the rear USB from the Radio to theĬomputer you should be able to test both CAT and PTT function. Scroll down to '232C RATE' and set to 38400bps.Īssuming you installed WSJT-X and it is running: Go Into the 101D FUNC Menu 'OPERATION SETTINGS' and select Now you are only interested in using the ' Enhanced' COMĬonnect the Yaesu provided USB cable between the Rear 101D USBĬonnector and a USB port on the computer. Number was 5 but may also be different on your computer.? Right A Second comport will show up as 'Silicon Labs DualĬP210x USB to UART Bridge 'Standard' COM Port (COMx)' My port Port (COMx)' where (COMx) in my windows setup as COM 9, it 'Silicon Labs Dual CP210x USB to UART Bridge Enhanced COM The installed driver will appear under Ports (COM (Virtual COM Port Driver) ? from the YaesuĪfter you install the driver verify it is working by using Windowsĭevice Manager. The first thing to do is download and install the ? FTDX101D/MP USB Driver Me to treat FT-8 as a SSB modulated mode using the 101D internal I say inĪdvance that there may be better ways to configure the 101D forįT-8 using the built-in digital modes. Modulate the FT-8 program from the 101D Rear USB Port. These are the settings I used to CAT control WSJT-X FT-8 and audio I will try to answer you the best that I can:

Really don't want to add a third party audio interface. The Yaesu provided CAT/Audio driver? If so, I can sure use the Has anyone tried to interface FT-8 using just the 101D USB port I don't know if it'sĭriver problem, hardware problem or just me problem. Keys but there is no audio modulation tones. However, In transmit I get no audio modulating the rig. When I run FT-8 I have CAT (reads both main and sub vfoĪnd beautiful line in audio waterfall. When setting up FT-8 soundcard input/output I select 'Line(USBĬODEC)' for the input and 'Speakers (USB AUDIO CODEC)' for the I confirm the driver is installed and working I downloaded and installed the USB Driver

I've been struggling to get my 101D interfaced to WJST-X FT8 using I really don't want to add a third party audio interface. Has anyone tried to interface FT-8 using just the 101D USB port running the Yaesu provided CAT/Audio driver? If so, I can sure use the help. I don't know if it's a driver problem, hardware problem or just me problem. The rig keys but there is no audio modulation tones. When I run FT-8 I have CAT (reads both main and sub vfo frequencies), and beautiful line in audio waterfall. When setting up FT-8 soundcard input/output I select 'Line(USB AUDIO CODEC)' for the input and 'Speakers (USB AUDIO CODEC)' for the output. I confirm the driver is installed and working properly using Windows device manager.

#USB AUDIO DRIVER WINDOWS 7#

I am running Windows 7 64bit operating system. I downloaded and installed the USB Driver (Virtual Port Driver) from the Yaesu website. Hello All, I've been struggling to get my 101D interfaced to WJST-X FT8 using the rear panel USB port.

Usb audio driver